产品分类
PRODUCT CATEGORIES
	              广美玻璃自动化科技
服务热线:13542572637400-8382-338
公司邮箱:2851717895@qq.com2851717891@qq.com
公司传真:0757-83686589
公司地址:佛山市南海区狮山科技工业园A区博学路2号GM-3060中空玻璃封胶线
Product summary An Chuan servo bus control system is adopted, with mature technology and stable and reliable operation. The gluing machine operates independently in four sections. When the glass length is more than 2 meters, it is linked as a whole. When the glass length is less than 2 meters, each section operates independently, which greatly improves the gluing speed. Electronic proportioning system is adopted to control the mixing ratio, which is convenient to adjust and accurate in proportioning. It is especially suitable for gluing curtain wall glass, and the amount of glue can be automatically adjusted according to the gluing width and depth, which can meet the requirements of aluminum strip width from 6A to 27A for efficient gluing. The input and output are transported by full servo motor, which has large bearing capacity and high transmission efficiency. The glued glass is output by V-belt transmission system, which can automatically center according to the glass thickness to prevent sticking. This machine can glue three glasses and two cavities at one time, and the gluing is clean and fast. Applicable glue types: two-component polysulfide glue or silicone sealing and silicone structural glue. Adopt motion controller and touch screen operating system, with simple operation and stable operation. Automatic thickness measuring system, which can automatically adjust the gluing data after automatically measuring the thickness of aluminum strip, is a truly humanized function, and it has been impossible to realize automation to solve the problem of loose sheets and miscellaneous sheets.
收藏
                13690317891
产品详情
全自动中空玻璃封胶线
一. MODEL:全自动中空玻璃封胶线 型号 GM-FJX2540 型二. GENERAL ARRANGEMENT 标准配置
(示意图仅供参考,不作为验收依据)
产品概要
Ø 采用日本安川伺服总线控制系统,技术成熟,运行稳定可靠。
Ø 打胶机采用四段式独立运行,当玻璃长度大于 2 米时整体联动,当玻璃长度小于 2 米时每段独立运行,大大提高打胶速度。
Ø 采用电子配比系统控制混胶比,调整方便,配比精确,特别适合幕墙玻璃打胶,胶量根据涂胶宽度和涂胶深度自动调整,可满足 6A 至 27A 的铝条宽高效打胶。
Ø 输入及输出采用全伺服电机输送,承载力大,传输效率高,涂胶后的玻璃采用 V 型带传输系统输出,能根据玻璃厚度自动对中,防止粘胶。
Ø 本机可实现三玻两腔玻璃一次打胶完成,涂胶干净快速。
Ø 适用胶种:双组份聚硫胶或者硅酮密封和硅酮结构胶。
Ø 采用 运动控制器, 触摸屏操作系统,操作简单,运行稳定。
Ø 自动测厚系统,自动测量铝条厚度后自动调节打胶的数据,真正的人性化功能,解决散单杂单一直无法实现自动化生产的难题。
Ø 自动修角装置,在打胶的同时自动对四个角部进行抹胶修正,打胶完成就直接是成品,角位美观实用。
标准配置由以下几部分组成:
1. 传输段 X 4(V 带特别设计,防磨损)
2. 吸盘(费斯托)
3. 控制台(人机智能控制系统)
4. 打胶控制系统(日本安川)
5. 打胶机头(多项专利,行业突破性设计)
压盘供胶系统(单双可供选
机械外形尺寸  | 13000mmx1600mmx3500mm  | 
可加工最大玻璃规格  | 3000mm x 6000mm  | 
可加工最小玻璃规格  | 300mm x 350mm  | 
涂胶厚度  | 6mm –30mm  | 
中空玻璃成品厚度  | 12mm – 60mm  | 
单片玻璃厚度  | 3-15mm  | 
打胶速度  | 4-40 米/分钟(6A 隔条、5mm 胶深规格条)  | 
传送速度  | 4 – 40m/min  | 
负载重量  | 3000kg/m  | 
打胶环境温度  | 15-40℃  | 
控制方式  | 触摸屏  | 
气源  | 气源压力 6Bar,最大耗气量 2.0Ms/min  | 
电压功率  | 12kw , 380V (50HZ)  | 
 外接线入口  | 
 10 ㎡电线 63A 断路器(5 线)  |